added a lazyinstall script for dev purposes

lazyinstall/README.md

@@ -0,0 +1,3 @@
+This is a very primitive script to automate the openwrt setup.
+It's probably best not used at this point.
+

lazyinstall/fstab

@@ -0,0 +1,21 @@
+#/etc/config/fstab from Meshenger project
+
+config global automount
+        option from_fstab 1
+        option anon_mount 1
+
+config global autoswap
+        option from_fstab 1
+        option anon_swap 0
+
+config mount
+        option target   /
+        option device   /dev/sda1
+        option fstype   ext4
+        option options  rw,sync
+        option enabled  1
+        option enabled_fsck 0
+
+config swap
+        option device   /dev/sda2
+        option enabled  0

lazyinstall/fstab_extroot

@@ -0,0 +1,21 @@
+#/etc/config/fstab from Meshenger project
+
+config global automount
+        option from_fstab 1
+        option anon_mount 1
+
+config global autoswap
+        option from_fstab 1
+        option anon_swap 0
+
+config mount
+        option target   /
+        option device   /dev/sda1
+        option fstype   ext4
+        option options  rw,sync
+        option enabled  1
+        option enabled_fsck 0
+
+config swap
+        option device   /dev/sda2
+        option enabled  1

lazyinstall/lazyinstall1.sh

@@ -0,0 +1,25 @@
+#!/bin/bash
+
+
+echo 'This is the meshenger lazy install!'
+echo 'It presumes your OpenWRT router has a connection to the internet'
+echo 'And that you have a properly formatted usb flash drive'
+echo 'more info + manual instructions: https://github.com/jngrt/meshenger'
+
+opkg update
+opkg install block-mount kmod-usb-storage kmod-usb2 kmod-fs-ext4
+
+mkdir /mnt/sda1
+mount -t ext4 /dev/sda1 /mnt/sda1
+
+echo 'Copying filesystem to USB drive'
+mkdir -p /tmp/cproot
+mount --bind / /tmp/cproot
+tar -C /tmp/cproot -cvf - . | tar -C /mnt/sda1 -xf
+umount /tmp/cproot
+
+mv fstab /etc/config/fstab
+
+echo 'Reboot'
+reboot -f
+

lazyinstall/lazyinstall2.sh

@@ -0,0 +1,31 @@
+#!/bin/bash
+
+
+echo 'This is the meshenger lazy install part two!'
+echo 'It presumes you already ran part 1!'
+echo 'You should review the settings of "wireless" and "network"'
+
+mkswap /dev/sda2
+swapon /dev/sda2
+
+mv fstab_extroot /etc/config/fstab
+
+head -n 10 /etc/config/wireless >> tmp_wireless
+cat wireless >> tmp_wireless
+mv tmp_wireless /etc/config/wireless
+rm tmp_wireless
+
+mv network /etc/config/network
+opkg update
+opkg install kmod-batman-adv kmod-ipv6
+
+sed -i -e "s/mesh/adhoc0/g" /etc/config/batman-adv
+
+opkg install python git
+git clone git://github.com/jngrt/meshenger.git
+
+echo 'my ip address is:'
+ifconfig  br-lan | grep 'inet addr'
+
+echo 'rebooting'
+reboot -f

lazyinstall/network

@@ -0,0 +1,20 @@
+config interface 'loopback'
+        option ifname   'lo'
+        option proto    'static'
+        option ipaddr   '127.0.0.1'
+        option netmask  '255.0.0.0'
+
+config interface 'lan'
+        option  ifname  'eth0'
+        option  type    'bridge'
+        option  proto   'static'
+        option  ipaddr  '192.168.1.115' #change me! 
+        option  netmask '255.255.255.0'
+        option  gateway '192.168.1.2' #change me!
+        list    dns     '8.8.8.8'
+
+config interface 'mesh'
+        option ifname   'adhoc0'
+        option mtu      '1528'
+        option proto    'none'
+

lazyinstall/wireless

@@ -0,0 +1,8 @@
+
+config wifi-iface	'wmesh'
+	option device 	'radio0'
+	option ifname	'adhoc0'
+	option network	'mesh'  
+	option mode		'adhoc'
+	option ssid		'mesh'          
+	option bssid	'66:66:66:66:66:66'