7.9 KiB
meshenger
Meshenger is a Forban-inspired messaging software used for a speculative broadcast communication project. The starting point is an electronic messaging system running on a wireless mesh network. The messages propagate through the network when devices that come in contact with each other synchronize their content. It is non-hierarchical, every node receives, relays and broadcasts messages.
Using Meshenger. Devices detect each other by continously broadcasting an identifier packet while listening to those of other nodes. As soon as two (or more) nodes detect each other they will try to synchronize the messages on each node.
The users of the network can interface with the nodes to send or receive messages by using the webbrowser of their smartphone or computer. The messages can be received and sent at any time, but they are only synchronized in the network when other nodes are encountered.
Meshenger is supposed to run on an Open-WRT router that has been configured to work in mesh networks (for a configuration how-to see below).
Configuring a router for Open-WRT and Meshenger
Flashing and preparing
Meshenger requires routers that both support Open-WRT and have at least one USB port (List of Open-WRT routers here). We have used the following models: TP-Link MR-3020, TP-Link TP-WR703n and TP-WR842nd.
Open-WRT have a guide for each supported device that tells how to best flash your specific device with Open-WRT. (Article on flashing)
After flashing proceed through the first login as described here.
You are going to need to have an internet connection to your router, the easiest thing is to hook it up to the router.
Alternatively if you use OSX you can enable internet sharing (make sure to set your OSX machine as the gateway and DNS server for your router in /etc/config/network)
System configuration
To use your router for Meshenger you're going to need to run the whole filesystem from a USB-Drive.
Make sure that said USB-Drive is formatted as such:
- one ext4 partition
- one linux-swap partition (32mb seems to be sufficient so far)
Next enable USB-Storage on the router:
$ opkg update
$ opkg install 'block-mount kmod-usb-storage kmod-usb2 kmod-fs-ext4
To check if it works try $ ls /dev/. You shoud see sda, sda1 and sda2
Now mount the USB-Drive:
$ mkdir /mnt/sda1
$ mount -t ext4 /dev/sda1 /mnt/sda1
Copy the whole filesystem to the USB-Drive:
$ mkdir -p /tmp/cproot
$ mount --bind / /tmp/cproot
$ tar -C /tmp/cproot -cvf - . | tar -C /mnt/sda1 -xf
$ umount /tmp/cproot
Edit fstab
$ vi /etc/config/fstab
Make config mount look like:
config mount
option target /
option device /dev/sda1
option fstype ext4
option options rw,sync
option enabled 1
option enabled_fsck 0
Reboot the device ($ reboot -f) and use $ df -h to confirm device now runs off the USB-Drive
Next we configure the swap partition
$ mkswap /dev/sda2
$ swapon /dev/sda2
Edit fstab again now make the swap look like this:
config mount
option device /dev/sda2
option enabled
Wireless configuration
The next section is on how to set up the network interfaces to work with B.A.T.M.A.N the mesh networking protocol. It is more or less a summary of what's written here.
$ vi etc/config/wireless and edit the wireless interface to look like this:
Dont forget to remove the line that disables wireless
config wifi-iface 'wmesh'
option device 'radio0'
option ifname 'adhoc0'
option network 'mesh'
option mode 'adhoc'
option ssid 'mesh'
option bssid '66:66:66:66:66:66'
Next up is $ vi etc/config/network where we add this interface:
config interface 'mesh'
option ifname 'adhoc0'
option mtu '1528'
option proto 'none'
Install B.A.T.M.A.N and IP6 support.
$ opkg install kmod-batman-adv kmod-ipv6
Then edit $ /etc/config/batman-adv to tell it which interface to use.
config mesh 'bat0'
option interfaces 'adhoc0'
option 'aggregated_ogms'
option 'ap_isolation'
option [..]
$ /etc/init.d/network restart to make the changes take effect.
If you have set this up properly on more than one node, the nodes should be able to see each other. Test with $ batctl -o
Make sure that you have the same version of batctl and openwrt on all nodes you plan to use.
$ uname -a && batctl -v to see the version information.
Configuring / Adding a client Hotspot
For the front-end, the client user interface, we must have a captive portal running. These are the first steps in enableing another wireless interface for the hotspot
Add the following lines in the following config files and restart the network:
$ vi /etc/config/network
config interface 'hotspot'
option 'iface' 'radio0' #use your excisting wifi device (look in config/wireless below)
option 'proto' 'static'
option 'ipaddr' '192.168.2.1'
option 'netmask' '255.255.255.0'
option 'type' 'bridge'
$ vi /etc/config/wireless
config wifi-iface
option 'device' 'radio0' #use your excisting wifi device, look in the list above.
option 'ssid' 'meshtest1'
option 'network' 'hotspot'
option 'mode' 'ap'
option 'encryption' 'none'
option 'isolate' '1'
$ vi /etc/config/dhcp
config dhcp hotspot
option 'interface' 'hotspot'
option 'start' '100'
option 'limit' '150'
option 'dynamicdhcp' '1'
$ vi /etc/config/firewall enable handing out dhcp addresses to wifi clients
config 'zone'
option 'name' 'hotspot'
option 'input' 'ACCEPT'
option 'forward' 'ACCEPT' #was REJECT
option 'output' 'ACCEPT'
config 'rule'
option 'src' 'hotspot'
option 'dest_port' '53'
option 'proto' 'tcpudp'
option 'target' 'ACCEPT'
config 'rule'
option 'src' 'hotspot'
option 'src_port' '67-68'
option 'dest_port' '67-68'
option 'proto' 'udp'
option 'target' 'ACCEPT'
$ /etc/init.d/network restart
$ /etc/init.d/firewall restart
$ /etc/init.d/dnsmasq restart
to serve file, run uhttpd server, for example in home folder:
$ /usr/sbin/uhttpd -f -p 8080 -h Meshenger/msg
the website will be available at 192.168.2.1:8080 from meshtest network.
easier is to maybe use the already running uhttpd, used by luci and change the config file? (to 'catch all' and 'forward all http' requests to correct folder) (/etc/httpd.conf or /etc/config/uhttpd)
make luci work on port 81, freeing port 80 for us (or disable luci completely)
$ vi /etc/config/uhttpd
$ /etc/init.d/uhttpd restart
this is not ideal ofcourse, but i cant get python to run on localhost port 80 and be accessible...
NOTES/TODO -maybe add extra port 80 rules in the firewall? -disable luci? /etc/init.d/uhttpd disable
Installing meshenger
Get the dependencies and clone the git
$ opkg install python git
$ git clone git://github.com/jngrt/meshenger.git