Browse Source

added images to the howto

master
then 4 years ago
parent
commit
01ad5b9a79
  1. 29
      electronics/README.md

29
electronics/README.md

@ -18,17 +18,42 @@
### Modding Coils/pads
If you have soldered all components together and your ESP12f won't boot, you might have to modifiy your charging coil+circuit a bit. To make sure it's the coild, measure the output of the coils electronics on the + and - (gnd) terminals. If your multimeter reads ~2.5 volts you need to modify the circuit. (Disclaimer: the exact details on how this circuit works are yet unclear, comparing to a working coil revealed several differences in the electronics, matching them up made the non working coil output the needed 5v).
If you have soldered all components together and your ESP12f won't boot, you might have to modifiy your charging coil+circuit a bit. To make sure it's the coil, measure the output of the coil's electronics on the + and - (gnd) terminals. If your multimeter reads ~2.5 volts you need to modify the circuit. (Disclaimer: the exact details on how this circuit works are yet unclear, comparing to a working coil revealed several differences in the electronics, matching them up made the non working coil output the needed 5v).
##### Step 1
Take off the follwing chips indicated by the following silkscreen printing:
You need to desolder two IC's/ chips following the (visual) guide below. The electronics and coil are sandwitched between two layers of foil. To peel the foil away look for an opening near the lightning connector.
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/001-coil.jpg)
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/002-peel.jpg)
You are then left over with the bare coil and flexible pcb. Here I already desoldered the lightning connector flex pcb.
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/003-bare-coil.jpg)
Remove the follwing chips indicated by the following silkscreen printing:
* Q3 (chip markings: p7)
* Q4 (chip markings: wsc7)
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/004-q3.jpg)
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/005-q4.jpg)
A hot air reworking station + tweezers will make quick work of that (settings: 1 second on 320deg, modertate airflow). Without hotair you could try a soldering iron or fine wirecutters to simply cut away the chips. The flexible PCB is very fragile though.
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/006-hotair.jpg)
Step 1 completed!
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/007-hotair-done.jpg)
##### Step 2
With both chips removed, you have to bridge two of the three (now) bare connections of the transitor Q4. I could not find a datasheet on this transitor so please refer to the photo's to see which pins.
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/008-bridge.jpg)
Done!
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/009-done.jpg)
Loading…
Cancel
Save