stripped metadata from coild mod, added it to readme

works/Dennis de Bel & Anton Jehle/paracity_gallery_v041/README.md

@@ -66,7 +66,7 @@ In this Archive you will find a 3d printable .stl file that will allow you to pr
 
 ## Software
 In this Archive you will find an Arduino sketch for the ESP8266 wireless chip. 
-
+In the Software folder
 
 ### Prerequisites
 
@@ -137,36 +137,36 @@ If you have soldered all components together and your ESP12f won't boot, you mig
 
 You need to desolder two IC's/ chips following the (visual) guide below. The electronics and coil are sandwiched between two layers of foil. To peel the foil away look for an opening near the lightning connector.
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/001-coil.jpg)
+![picture](electronics/coil-mod/001-coil.jpg)
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/002-peel.jpg)
+![picture](electronics/coil-mod/002-peel.jpg)
 
 You are then left over with the bare coil and flexible pcb. Here I already desoldered the lightning connector flex pcb.
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/003-bare-coil.jpg)
+![picture](electronics/coil-mod/003-bare-coil.jpg)
 
 
 Remove the following chips indicated by the following silkscreen printing:
 * Q3 (chip markings: p7)
 * Q4 (chip markings: wsc7)
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/004-q3.jpg)
+![picture](electronics/coil-mod/004-q3.jpg)
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/005-q4.jpg)
+![picture](electronics/coil-mod/005-q4.jpg)
 
 A hot air reworking station + tweezers will make quick work of that (settings: 1 second on 320deg, moderate airflow). Without hot-air you could try a soldering iron or fine wire-cutters to simply cut away the chips. The flexible PCB is very fragile though.
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/006-hotair.jpg)
+![picture](electronics/coil-mod/006-hotair.jpg)
 
 Step 1 completed!
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/007-hotair-done.jpg)
+![picture](electronics/coil-mod/007-hotair-done.jpg)
 
 ##### Step 2
 
 With both chips removed, you have to bridge two of the three (now) bare connections of the transistor Q4. I could not find a datasheet on this transistor so please refer to the photo's to see which pins.
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/008-bridge.jpg)
+![picture](electronics/coil-mod/008-bridge.jpg)
 
 Done!
 
-![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/009-done.jpg)
+![picture](electronics/coil-mod/009-done.jpg)

works/Dennis de Bel & Anton Jehle/paracity_gallery_v041/flash_this_code_on_esp/README.md

@@ -1,45 +0,0 @@
-# opencoil-paracity: code
-
-### Prerequisites
-
-This guide assumes you have a 4MB ESP12F microcontroller and use Arduino IDE.
-
-* Board Manager: You will need to add the support for this board to your IDE (Arduino in this case), see: https://github.com/esp8266/Arduino
-* SPIFFS: You will need to add SPIFFS file upload support to Arduino if you want to upload files to the ESP12F, see: https://github.com/esp8266/arduino-esp8266fs-plugin
-
-
-
-### Uploading Code
-For ESP12F use the following settings in Arduino IDE
-
-* Board: Generic ESP8266 Module
-* Builtin Led: 2
-* Upload Speed: 921600
-* CPU Frequency: 80 MHz
-* Crystal Frequency: 26MHz
-* Flash Size: 4MB (FS:3MB OTA: ~512KB) 
-* Flash Mode: DOUT
-* Flash Frequency: 40MHz
-* Reset Method: dtr (aka nodemcu)
-* Debug port: Disabled
-* Debug Level: none
-* LwIP Variant: v2 Lower Memory
-* VTables: Flash
-* Exceptions: Legacy (new can return nullptr)
-* Erase Flash: depends on if you want to change SSID, Files, or only Sketch
-* Espressif FW: nonos-sdk 2.2.1+100 (190703)
-* SSL Support: All SSL ciphers (most compatible)
-* Port: depend if u are uploading Over The Air, or using a cable
-* Programmer: AVRISP mkII
-
-
-These settings give you about 2.471 KB of SPIFFS storage space for files and ~512KB sketch size
-
-
-### Over The Air (OTA) Uploading 
-
-* Connect to the hotspot created by the ESP12F.
-* Launch Arduino, choose "esp at 192.168.4.1" as the port. 
-* If you don't see the port listed in Arduino (Tools > Port), restart Arduino IDE.
-
-You can upload your sketch and files wirelessly, there is one caveat: SPIFFS file uploads don't work with password protected uploads (line 42). Workaround: flash your sketch with line 42 commented out. Upload your files to SPIFFS, then uncomment the line and Upload the code.

works/Dennis de Bel & Anton Jehle/paracity_gallery_v041/flash_this_code_on_esp/paracity_gallery_v041/DNSServer.cpp

@@ -1,166 +0,0 @@
-#include "./DNSServer.h"
-#include <lwip/def.h>
-#include <Arduino.h>
-
-#define DEBUG
-#define DEBUG_OUTPUT Serial
-
-DNSServer::DNSServer()
-{
-  _ttl = htonl(60);
-  _errorReplyCode = DNSReplyCode::NonExistentDomain;
-}
-
-bool DNSServer::start(const uint16_t &port, const String &domainName,
-                     const IPAddress &resolvedIP)
-{
-  _port = port;
-  _domainName = domainName;
-  _resolvedIP[0] = resolvedIP[0];
-  _resolvedIP[1] = resolvedIP[1];
-  _resolvedIP[2] = resolvedIP[2];
-  _resolvedIP[3] = resolvedIP[3];
-  downcaseAndRemoveWwwPrefix(_domainName);
-  return _udp.begin(_port) == 1;
-}
-
-void DNSServer::setErrorReplyCode(const DNSReplyCode &replyCode)
-{
-  _errorReplyCode = replyCode;
-}
-
-void DNSServer::setTTL(const uint32_t &ttl)
-{
-  _ttl = htonl(ttl);
-}
-
-void DNSServer::stop()
-{
-  _udp.stop();
-}
-
-void DNSServer::downcaseAndRemoveWwwPrefix(String &domainName)
-{
-  domainName.toLowerCase();
-  domainName.replace("www.", "");
-  domainName.replace("https://", "");
-}
-
-void DNSServer::processNextRequest()
-{
-  _currentPacketSize = _udp.parsePacket();
-  if (_currentPacketSize)
-  {
-    _buffer = (unsigned char*)malloc(_currentPacketSize * sizeof(char));
-    _udp.read(_buffer, _currentPacketSize);
-    _dnsHeader = (DNSHeader*) _buffer;
-
-    if (_dnsHeader->QR == DNS_QR_QUERY &&
-        _dnsHeader->OPCode == DNS_OPCODE_QUERY &&
-        requestIncludesOnlyOneQuestion() &&
-        (_domainName == "*" || getDomainNameWithoutWwwPrefix() == _domainName)
-       )
-
-    {
-      replyWithIP();
-    }
-    else if (_dnsHeader->QR == DNS_QR_QUERY)
-    {
-      replyWithCustomCode();
-    }
-
-    free(_buffer);
-  }
-}
-
-bool DNSServer::requestIncludesOnlyOneQuestion()
-{
-  return ntohs(_dnsHeader->QDCount) == 1 &&
-         _dnsHeader->ANCount == 0 &&
-         _dnsHeader->NSCount == 0 &&
-         _dnsHeader->ARCount == 0;
-}
-
-String DNSServer::getDomainNameWithoutWwwPrefix()
-{
-  String parsedDomainName = "";
-  unsigned char *start = _buffer + 12;
-  if (*start == 0)
-  {
-    return parsedDomainName;
-  }
-  int pos = 0;
-  while(true)
-  {
-    unsigned char labelLength = *(start + pos);
-    for(int i = 0; i < labelLength; i++)
-    {
-      pos++;
-      parsedDomainName += (char)*(start + pos);
-    }
-    pos++;
-    if (*(start + pos) == 0)
-    {
-      downcaseAndRemoveWwwPrefix(parsedDomainName);
-      return parsedDomainName;
-    }
-    else
-    {
-      parsedDomainName += ".";
-    }
-  }
-}
-
-void DNSServer::replyWithIP()
-{
-  _dnsHeader->QR = DNS_QR_RESPONSE;
-  _dnsHeader->ANCount = _dnsHeader->QDCount;
-  _dnsHeader->QDCount = _dnsHeader->QDCount; 
-  //_dnsHeader->RA = 1;  
-
-  _udp.beginPacket(_udp.remoteIP(), _udp.remotePort());
-  _udp.write(_buffer, _currentPacketSize);
-
-  _udp.write((uint8_t)192); //  answer name is a pointer
-  _udp.write((uint8_t)12);  // pointer to offset at 0x00c
-
-  _udp.write((uint8_t)0);   // 0x0001  answer is type A query (host address)
-  _udp.write((uint8_t)1);
-
-  _udp.write((uint8_t)0);   //0x0001 answer is class IN (internet address)
-  _udp.write((uint8_t)1);
- 
-  _udp.write((unsigned char*)&_ttl, 4);
-
-  // Length of RData is 4 bytes (because, in this case, RData is IPv4)
-  _udp.write((uint8_t)0);
-  _udp.write((uint8_t)4);
-  _udp.write(_resolvedIP, sizeof(_resolvedIP));
-  _udp.endPacket();
-
-
-
-  #ifdef DEBUG
-    DEBUG_OUTPUT.print("DNS responds: ");
-    DEBUG_OUTPUT.print(_resolvedIP[0]);
-    DEBUG_OUTPUT.print(".");
-    DEBUG_OUTPUT.print(_resolvedIP[1]);
-    DEBUG_OUTPUT.print(".");
-    DEBUG_OUTPUT.print(_resolvedIP[2]);
-    DEBUG_OUTPUT.print(".");
-    DEBUG_OUTPUT.print(_resolvedIP[3]);
-    DEBUG_OUTPUT.print(" for ");
-    DEBUG_OUTPUT.println(getDomainNameWithoutWwwPrefix());
-  #endif
-}
-
-void DNSServer::replyWithCustomCode()
-{
-  _dnsHeader->QR = DNS_QR_RESPONSE;
-  _dnsHeader->RCode = (unsigned char)_errorReplyCode;
-  _dnsHeader->QDCount = 0;
-
-  _udp.beginPacket(_udp.remoteIP(), _udp.remotePort());
-  _udp.write(_buffer, sizeof(DNSHeader));
-  _udp.endPacket();
-}

works/Dennis de Bel & Anton Jehle/paracity_gallery_v041/flash_this_code_on_esp/paracity_gallery_v041/DNSServer.h

@@ -1,72 +0,0 @@
-#ifndef DNSServer_h
-#define DNSServer_h
-#include <WiFiUdp.h>
-
-#define DNS_QR_QUERY 0
-#define DNS_QR_RESPONSE 1
-#define DNS_OPCODE_QUERY 0
-
-enum class DNSReplyCode
-{
-  NoError = 0,
-  FormError = 1,
-  ServerFailure = 2,
-  NonExistentDomain = 3,
-  NotImplemented = 4,
-  Refused = 5,
-  YXDomain = 6,
-  YXRRSet = 7,
-  NXRRSet = 8
-};
-
-struct DNSHeader
-{
-  uint16_t ID;               // identification number
-  unsigned char RD : 1;      // recursion desired
-  unsigned char TC : 1;      // truncated message
-  unsigned char AA : 1;      // authoritive answer
-  unsigned char OPCode : 4;  // message_type
-  unsigned char QR : 1;      // query/response flag
-  unsigned char RCode : 4;   // response code
-  unsigned char Z : 3;       // its z! reserved
-  unsigned char RA : 1;      // recursion available
-  uint16_t QDCount;          // number of question entries
-  uint16_t ANCount;          // number of answer entries
-  uint16_t NSCount;          // number of authority entries
-  uint16_t ARCount;          // number of resource entries
-};
-
-class DNSServer
-{
-  public:
-    DNSServer();
-    void processNextRequest();
-    void setErrorReplyCode(const DNSReplyCode &replyCode);
-    void setTTL(const uint32_t &ttl);
-
-    // Returns true if successful, false if there are no sockets available
-    bool start(const uint16_t &port,
-              const String &domainName,
-              const IPAddress &resolvedIP);
-    // stops the DNS server
-    void stop();
-
-  private:
-    WiFiUDP _udp;
-    uint16_t _port;
-    String _domainName;
-    unsigned char _resolvedIP[4];
-    int _currentPacketSize;
-    unsigned char* _buffer;
-    DNSHeader* _dnsHeader;
-    uint32_t _ttl;
-    DNSReplyCode _errorReplyCode;
-
-    void downcaseAndRemoveWwwPrefix(String &domainName);
-    String getDomainNameWithoutWwwPrefix();
-    bool requestIncludesOnlyOneQuestion();
-    void replyWithIP();
-    void replyWithCustomCode();
-};
-#endif
-

works/Dennis de Bel & Anton Jehle/paracity_gallery_v041/flash_this_code_on_esp/paracity_gallery_v041/data/index.html

@@ -1,12 +0,0 @@
-<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd">
-<html>
-
-	<head>
-		<title></title>
-	</head>
-	<body>
-
-hi
-<img src="pic.jpg">
-	</body>
-</html>

works/Dennis de Bel & Anton Jehle/paracity_gallery_v041/flash_this_code_on_esp/paracity_gallery_v041/paracity_gallery_v041.ino

@@ -1,98 +0,0 @@
-  // Captive portal with (arduino) OTA + SPIFFS
-  
-  #include <Arduino.h>
-  #include <ESP8266WiFi.h>
-  #include <ESP8266mDNS.h>
-  #include <WiFiUdp.h>
-  #include <ArduinoOTA.h> // Over-the-Air updates
-  #include <ESP8266WebServer.h>
-  #include "./DNSServer.h" // Dns server
-  #include <FS.h> // SPIFFS
-  
-  DNSServer dnsServer;
-  const byte DNS_PORT = 53;
-  
-  ESP8266WebServer server(80);
-
-  #ifndef STASSID
-  #define STASSID "\xF0\x9F\x9B\xB4 UNFLASHED"
-  //#define STASPSK "mypassword"
-  #endif
-
-  IPAddress apIP(192, 168, 4, 1);
-  const char* ssid = STASSID;
-  //const char* password = STAPSK;
-
-  void setup() {
-    Serial.begin(115200);
-    Serial.println("Booting");
-
-    WiFi.mode(WIFI_AP);
-    WiFi.softAPConfig(apIP, apIP, IPAddress(255, 255, 255, 0));
-    WiFi.softAP(ssid);
-    dnsServer.start(DNS_PORT, "*", apIP); // redirect dns request to AP ip
-    
-    MDNS.begin("esp8266", WiFi.softAPIP());
-    Serial.println("Ready");
-    Serial.print("IP address: ");
-    Serial.println(WiFi.softAPIP());
-
-    //Over-the-Air updates
-    ArduinoOTA.setHostname("ESP8266");
-    //ArduinoOTA.setPassword("change-me"); //disabled to allow data uploads
-    ArduinoOTA.begin();
-    SPIFFS.begin();
-
-     //redirect all traffic to index.html
-  server.onNotFound([]() {
-    if(!handleFileRead(server.uri())){
-      const char *metaRefreshStr = "<head><meta http-equiv=\"refresh\" content=\"0; url=http://192.168.4.1/index.html\" /></head><body><p>redirecting...</p></body>";
-      server.send(200, "text/html", metaRefreshStr);
-    }
-  });
-  
-    server.begin();
-
-  }
-
-  void loop() {
-     dnsServer.processNextRequest();
-    ArduinoOTA.handle();
-    server.handleClient();
-    delay(50);
-  }
-
-
-String getContentType(String filename){
-  if(server.hasArg("download")) return "application/octet-stream";
-  else if(filename.endsWith(".htm")) return "text/html";
-  else if(filename.endsWith(".html")) return "text/html";
-  else if(filename.endsWith(".css")) return "text/css";
-  else if(filename.endsWith(".js")) return "application/javascript";
-  else if(filename.endsWith(".png")) return "image/png";
-  else if(filename.endsWith(".gif")) return "image/gif";
-  else if(filename.endsWith(".jpg")) return "image/jpeg";
-  else if(filename.endsWith(".ico")) return "image/x-icon";
-  else if(filename.endsWith(".xml")) return "text/xml";
-  else if(filename.endsWith(".mp4")) return "video/mp4";
-  else if(filename.endsWith(".pdf")) return "application/x-pdf";
-  else if(filename.endsWith(".zip")) return "application/x-zip";
-  else if(filename.endsWith(".gz")) return "application/x-gzip";
-  return "text/plain";
-}
-
-//Given a file path, look for it in the SPIFFS file storage. Returns true if found, returns false if not found.
-bool handleFileRead(String path){
-  if(path.endsWith("/")) path += "index.html";
-  String contentType = getContentType(path);
-  String pathWithGz = path + ".gz";
-  if(SPIFFS.exists(pathWithGz) || SPIFFS.exists(path)){
-    if(SPIFFS.exists(pathWithGz))
-      path += ".gz";
-    File file = SPIFFS.open(path, "r");
-    size_t sent = server.streamFile(file, contentType);
-    file.close();
-    return true;
-  }
-  return false;
-}