|
|
|
@ -27,7 +27,7 @@ The two most important things to take into consideration before starting are |
|
|
|
|
|
|
|
- Choosing a "route" through this documentation (see just below). |
|
|
|
- Reading the [Prerequisites] section very closely and trying to |
|
|
|
understand, **before** you dive in, how things will work with your Raspberry |
|
|
|
understand, **before you dive in**, how things will work with your Raspberry |
|
|
|
Pi and how it is setup and connected to the internet. |
|
|
|
|
|
|
|
There are 3 routes you can take through this documentation: |
|
|
|
@ -74,14 +74,23 @@ the command-line. |
|
|
|
|
|
|
|
Here is an example of what we did. |
|
|
|
|
|
|
|
*Below: Here we plug the grey ethernet cable into our Router.* |
|
|
|
*Below: Here we plug the gray ethernet cable into the router.* |
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
*Below: And here we plug that cable into the Raspberry pi.* |
|
|
|
*Below: And then we plug that same gray ethernet cable into the Raspberry Pi.* |
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
!!! note |
|
|
|
|
|
|
|
The ethernet cable is not required after you finish the installation |
|
|
|
of Bibliotecha! Your Bibliotecha can now operate independent of an internet |
|
|
|
connection and offers its own Wifi access point. So, the ethernet cable is only |
|
|
|
required for the installation process. Later, if you need to do an update or |
|
|
|
some maintenance which requires an internet connection, you can plug it back in |
|
|
|
and [make sure to check this tip]. |
|
|
|
|
|
|
|
The current latest [Raspberry Pi 3 B+] model is recommended. This model is |
|
|
|
chosen because it offers a built-in wireless card for convenient networking and |
|
|
|
a sufficient memory allowance of 1GB. It is possible to use other models of |
|
|
|
@ -99,12 +108,13 @@ $ sudo lsblk # to see the value for the `of` argument (e.g. /dev/mmcblk0) |
|
|
|
$ sudo dd bs=4M if=2020-08-20-raspios-buster-armhf-lite.img of=<YOUR-DEVICE-HERE> status=progress conv=fsync |
|
|
|
``` |
|
|
|
|
|
|
|
[raspberry pi]: https://www.raspberrypi.org/ |
|
|
|
[dd command]: https://www.raspberrypi.org/documentation/installation/installing-images/linux.md |
|
|
|
[etcher]: https://www.balena.io/etcher/ |
|
|
|
[make sure to check this tip]: #i-cannot-connect-to-the-internet-from-the-raspberry-pi |
|
|
|
[official setup documentation]: https://www.raspberrypi.org/documentation/setup/ |
|
|
|
[raspberry pi 3 b+]: https://www.raspberrypi.org/products/raspberry-pi-3-model-b/ |
|
|
|
[raspberry pi os]: https://www.raspberrypi.org/documentation/raspbian/ |
|
|
|
[etcher]: https://www.balena.io/etcher/ |
|
|
|
[dd command]: https://www.raspberrypi.org/documentation/installation/installing-images/linux.md |
|
|
|
[raspberry pi]: https://www.raspberrypi.org/ |
|
|
|
|
|
|
|
## Pre-installation |
|
|
|
|
|
|
|
|
